Tool Checklist
Impact driver
Used for driving bolts and screws of all types and sizes

Drill
Used for drilling holes

Heat gun
To heat shrink when making own coax cables

Angle grinder
To cut through metal (e.g., aluminum angle or strut channels) Note: Need to buy cut-off wheel seperately.

Rotary Hammer
For drilling into rock or concrete. Fits SDS plus bits.

Dewalt batteries (Spares)
Always have lots of spares ready and charged.

Deep impact sockets, 1/2" drive (7/16”, 1/2", 9/16”, 15/16")
Only 4 sizes needed. Important to get non-chrome plated since impact driver will cause them to chip.

Standard metric socket set (1/4 " drive)
7mm, 8mm, and 10 mm are used most for assembling ZDA antennas.

Hex socket adapters (1/4", 3/8", 1/2")
Attaches to impact driver for use with deep impact sockets.

Impact Hex Nutsetter bit (1/4" and 5/16")
Used with hose clamps (1/4") and self-tapping screws (5/16")

Impact Bit Set
Mainly for Roberson's (square) and Phillip's (cross) bits. It's handy to have multiple of each on a holder like this (with a carabiner).

Mini screw driver set
Better to get individual screwdrivers than interchangeable bits since it's easy to lose pieces.

Automatic wire strippers
There are two varieties that exist - either will work.

Wire rope cutter
For cutting guy wire. Don't go cheap with these - get the expensive ones!

Channel locks
Handy for all sorts of things. Get a brand name pair - non-brand versions can be very frustrating to use

Wrenches (7/16”, 1/2", 9/16”, 15/16", 10mm)
Helpful to have in addition to the sockets. Don't get the ratcheting wrenches.

SDS plus masonry bit (5/8” x 6")
For drilling in anchors to rock or concrete

Swage tool
For crimping guy wire sleeves

Bolt cutters
Sometimes bolts get cross-threaded or corroded and need to be cut off.

Level
For making sure the tower structure is vertical.

Compass or compass app on phone
To checking antenna directions.

Mini sledge
To drive in anchors.

Hammer
Helpful for moving stubborn housing brackets.

Multibit screwdriver
For (un)tightening screws.

Phillips (cross) screwdriver
Backup to multibit screwdriver.

Drill bit kit (Cobalt)
For drilling pilot holes or bolt holes.

Bridge reamers (3/8", 1/2", 5/8", 3/4")
For creating clean, even bolt holes in metal.

Clear plastic tubing (3/8" , 12" long)
To clear dust from holes drilled into rock or concrete

Safety Glasses
Use whenever using drill or rock hammer, or when working under someone.

Hard hat
Use whenever working below equipment or people.

Work gloves
Use to keep hands clean and safe from injury.

Fall protection
For working from heights. Check local rules and regulations for equipment and certification required.

N-95 masks
Use whenever drilling into rock, concrete, or metal.

Tape measure
For measuring.

In-line wire tensioner tool
Makes tensioning guy wire spools a whole lot easier.

Ratchet wrench (1/2" drive)
A backup for impact driver as well as in-line wire tensioner tool

Ratchet wrench (1/4" drive)
A backup for impact driver

RG58 Coax Wire Stripper
Used for thinner coax cables, such as RG58

LMR400 Coax Wire Stripper
Used exclusively for LMR400

Ratcheting Coax Crimper
For crimping on coax connectors

Coax Cutter
For cutting coax cable

Spade bits (1/2" and 1 1/2")
For drilling deep holes through walls to allow for AC extension cord (1/2") or coax cables (1 1/2").

Hole saw (2 1/2")
A) For drilling shallow holes through walls to allow for AC extension cord (1/2") or coax cables (1 1/2"). B) Or for making holes in storage boxes (e.g., Action Packers) for elbow joint.
Note: Important to get hole saw with the right-fitting shaft.

Step drill bit (3/8" driver, 1/4" - 1-3/8" hole sizes)
For drilling shallow holes through polycase.

Tool belt
There are several different styles - get one that suits you the best!

Tool belt drill holster
For holding small power tools.

Tool box
For storing tools.

Parts organizer
For sorting all the various nuts, bolts, screws, or other small spare parts.

Ladder
For attaching house brackets of lattice tower to building and accessing equipment at heights.
With very tall tower, may be accomplished safer with a lift.

Utility knife
Mainly to open boxes and packages.

Flush cutter
Cleanly cutting cable tie ends.

Crimping tool pliers with cutter
Cutting electrical wire and crimping terminal ends connectors.

Diagonal cutting pliers
Snipping wires, cutting of cable tie ends, etc.

Digital multimeter
To check voltages of solar setup, continuity, and wire resistance.

Contactless AC circuit tester
For checking if outlets are working and to see if there are wires within walls.

Laptop
For checking station interface and downloading data.

microSD adaptor
For installing software on raspberry pi and transferring data off SD card.

USB to ethernet adapter
Needed for wired connection to SensorStation. May also be needed if laptop is missing Ethernet port.

Ethernet cable
For wired connection to SensorGnome or SensorStation.

USB flash drive
Used for downloading data or configuring Wi-Fi on SensorStations

Soapstone Marker
To mark measurements on metal. Also called a welder's marker.

Flagging tape
Can be helpful when transporting large items, also for flagging certain tools so it doesn't get lost in the field. Also good to mark guy wires so they are visible.

NanoVNA
Used as an antenna analyser. Can check whether an antenna is damaged/unsuitable for use.

Ground rod driver
To help drive rebar into tough ground.
Must be compatible with rotary hammer.

1" x 3' Drive Rod
To help hammer in ground anchors into soft ground

Last updated
